Waldorf, Maryland
Whirlpool and Maytag Appliance Service in Waldorf, Maryland, with the published national price range up front, the failed part confirmed by testing on site, and the repair price stated before any work begins.
Walk through the laundry rooms of St. Charles and you will find Whirlpool and Maytag badges on a large share of the machines. The two brands sit under one parent company, and their washers, dryers, refrigerators, dishwashers, and ranges share many parts families and failure patterns. We service both brands across every appliance type, and we diagnose by testing, not by swapping parts until something works.
Laundry is where these brands earn their keep locally. We repair top load and front load washers that will not drain, will not spin, stop mid cycle, or leak at hoses and tub seals, and dryers that run without heat, squeak on worn rollers, or shut off early. In the kitchen, we repair their refrigerators with cooling and defrost problems, dishwashers that leave grit or standing water, and ranges with failed burners and igniters.
Because the two lines share so much under the cabinet, knowing one brand's layout helps with the other: a Maytag and a Whirlpool top loader of the same era often fail at the same pumps, switches, and drive parts. The model number tells us which parts family your machine belongs to, which is why we ask for it in the quote form — it decides the parts and repair path before anyone picks up a tool.
A Maytag top load washer in a St. Charles home stopped with a full tub of wet laundry inside. Testing showed power reaching the pump and a motor that hummed without turning; pulled out, the pump held a small sock seized in its impeller, its motor burned out against the strain. We replaced the pump, checked the drain hose and tub outlet for more debris, and ran a full cycle through drain and spin to confirm the repair.
No Waldorf shop publishes a local price list, so we publish the national ranges openly. From Angi's 2026 data: washer repair runs $50 to $450 nationally, dryer repair $100 to $400, refrigerator repair $200 to $300, and dishwasher repair $160 to $300. Across all appliances, the average repair nationally is about $170, with most jobs between $100 and $240. Where yours falls depends on the failed part and the hours involved, and we state the figure once testing confirms what failed.
Start with the quote form at the bottom of this page: the appliance, the brand, the symptom, and the model number from the label inside the door or on the back panel. On site, we test before we open the machine, confirm the component at fault, and replace parts matched by part number to your model. Every repair ends with the machine run through its paces, so the fix is proven, not assumed.
Use the quote form at the bottom of this page. Tell us whether the machine is a Whirlpool or a Maytag, which appliance it is, and what it is doing, plus the model number if you have it. We will respond with the published range for your repair and the next step.
Yes — both brands, across washers, dryers, refrigerators, dishwashers, ovens, and ranges. The two lines share a parent company and many parts families, so they are diagnosed the same way: test the failure, confirm the part, match the replacement to the model number.
Published national ranges from Angi put washer repair at $50 to $450, dryer repair at $100 to $400, refrigerator repair at $200 to $300, and dishwasher repair at $160 to $300, with the average repair overall at about $170. Your figure depends on the failed component, and we state it after testing confirms the fault.
The drain pump is the most common answer, followed by a blockage in the pump, drain hose, or tub outlet — socks and pocket debris are the usual culprits. A lid switch fault can also stop a top loader before drain and spin. Testing at the pump separates those causes quickly.
It does. Parts families change by production run even within the same brand, and the model number matches a pump, board, or element to your exact machine. The label sits inside the door, on the frame, or on the back panel, and including it in the quote form speeds everything up.
Most single fault repairs take about one to two hours on site once the part is confirmed. If a part must be ordered for a less common model, we give you the timing up front, plus how to use or rest the machine safely meanwhile.
Often, yes. Elements, thermal fuses, belts, and rollers are modest repairs, and a sound dryer can give years more service after one. The exception is a machine with several systems wearing at once; then we will say so and walk through the math with you.
Tell us which appliance is down and what it is doing. We read every request that comes in and respond with the published national range for that kind of repair and the next step, starting with a visit to test and confirm the failed part on site.
Prefer to talk it through first? Send the form and we will call you back at the number you give us.